Retro｜Schulz Air Compressor V Series 580HV20X-1 5 HP 80 Gallon Two Stage 230V 1 Phase｜ Other Products

Schulz 580HV20X-1: an 80-gallon two-stage compressor that stands 42 inches tallHeight is the reason this model exists. Its published dimensions are 56 inches long, 23 inches wide and 42 inches high — roughly bench height, and around half the height of the upright 80-gallon machines it shares a pump with. If your ceiling is low, your garage door track is in the way, or you want the compressor tucked along a wall or under a mezzanine instead of standing in the middle of the floor, that number is the whole decision.Everything above the tank is standard V-Series: a 5 HP WEG motor on 230V 1-phase power, a solid cast iron two-stage pump delivering 20 CFM at 175 PSI, and an 80-gallon ASME air receiver. The unusual part is the package it comes in.Before you plan the space: confirm the tank orientationPublished figures for this machine's tank orientation differ, and you should know that before you measure a wall.
The description that has been on this page describes an 80-gallon vertical tank.
The manufacturer specification fields we hold — both the tank orientation field and the structured spec sheet — say horizontal.
Both readings are shown here, each attributed to its source. The dimensions are consistent across every source we hold: 56 long by 23 wide by 42 high, which is a long, low package rather than a tall one. If the orientation is load-bearing for your install — a low ceiling, a specific alcove, a shelf above it — contact us and we will confirm it with Schulz in writing before you order.Will It Fit?

Overhead: at 42 inches, this clears under most mezzanines, storage racks and up-and-over door tracks that stop a full-height machine. Measure to the lowest obstruction, not the roof.

Floor: 56 inches by 23 inches. That is a longer, narrower plan than an upright machine, so it wants a wall run rather than a corner. Leave access along the belt-guard side for servicing and around the tank drain.

Weight: 524 lbs. Schulz publishes no minimum slab thickness or concrete rating for this model, so we are not going to state one. On a normal shop floor it is a non-issue; on a suspended floor or a thin residential pad, check before delivery day.

Power: 230V, 1-phase, with a mounted and prewired magnetic starter. The amp draw and breaker fields on the Schulz data sheet both read consult a certified electrician — the correct breaker depends on your run length, conductor and local code, so size it on site rather than from any web page.

Plumbing: a 1/2-inch tank outlet. Whatever you run downstream, the pipe is what decides delivered pressure at the tool; undersized line kills the benefit of a big tank faster than anything else.
Confirming ceiling, floor and circuit before ordering is the buyer's responsibility.What 20 CFM at 175 PSI actually means for your bayThe two numbers do different jobs. 175 PSI is what the tank will hold; 20 CFM is what the pump will keep replacing. Pressure is stored energy, flow is sustained work, and it is flow that decides whether a job stalls.A two-stage pump gets to that pressure in two bites — a large low-pressure cylinder feeds a smaller high-pressure one — which is why two-stage machines reach 175 PSI while single-stage units typically top out much lower. The practical value of storing air at high pressure in a large tank is that the usable band between cut-in and cut-out is wide, so the motor spends less of its life starting and stopping. Short-cycling is what kills compressors, and tank volume plus two-stage pressure is the cure for it.The V-cylinder pump and why the layout mattersThe V-Series takes its name from the angle between its cylinders. Splaying them apart opens up airflow between the two barrels and leaves room for deeper cooling fins on each, so the block sheds heat instead of storing it. A cooler pump means cooler discharge air, slower oil oxidation and longer valve life — heat is the mechanism behind almost every way a compressor pump dies.The block is solid cast iron rather than aluminium: heavier, but it conducts heat away and damps vibration. Inside are oversized main bearings, Swedish steel valves and CNC-machined components; outside, notched belts run inside an enclosed guard that keeps the drive away from hands and sleeves. Lubrication is a splash system with an oil sight glass so a level check is a glance, and there is no low-oil shut-off, which makes that glance part of your weekly routine. Note also that this model's spec lists no after-cooler and no air dryer, so downstream moisture treatment is on you if the work needs it.Perfect For

Low-ceiling garages and basement shops where a full-height compressor is simply not installable.

Service bays wanting the tank under a bench run or behind the lift rather than occupying floor space.

Fleet and municipal workshops running impact tools all day, where recovery between jobs is what costs time.

Fabrication and finishing work needing sustained flow at working pressure, not a headline peak figure.
What Is Fitted
WEG electric motor, 5 HP
V-Series solid cast iron two-stage pump, belt driven
Mounted and prewired magnetic starter
Oversized main bearings and Swedish steel valves
CNC-machined components
Notched belts with an enclosed belt guard
Powder-coated components
80-gallon ASME air receiver with safety valve and a 1/2-inch outlet
Pressure gauge and oil sight glass
SpecificationsMotor and power

Motor
5 HP, WEG

Voltage
230V AC

Phase
1-phase

Starter
Magnetic, mounted and prewired

Amp draw / breaker
Consult a certified electrician

Pump and output

Output
20 CFM

Rated at
175 PSI

Maximum pressure
175 PSI

Type
Two-stage, belt drive, solid cast iron

Lubrication
Oil lubricated, splash, sight glass

After-cooler / air dryer
No / No

Tank and dimensions

Tank
80-gallon (orientation: see the note above)

Tank outlet
1/2-inch

Length
56 inches

Width
23 inches

Height
42 inches

Weight
524 lbs

Certification, stated plainlyOne certification appears in this compressor's data: ASME, on the air receiver and safety valve. It is a pressure-vessel standard, and on a machine holding 80 gallons at 175 PSI it is the one that counts, because a tank is the component whose failure cannot be walked back.What it is not is an electrical safety listing or a whole-machine third-party approval, and we would rather say so than let the word carry more weight than it should. If a facility standard, an inspector or an insurer requires a particular electrical listing on fixed equipment, ask us first and we will confirm what this unit carries in writing.Shipping and DeliveryFreight only, within the lower 48 states, quoted live at checkout against your actual address so the number is current rather than an estimate printed months ago.Decide how it comes off the truck before you order. A crated 524 lb compressor needs a forklift, a pallet jack and a dock, or a trailer at a freight terminal — no driver will carry it inside for you. Residential delivery is available and carries a fee shown at checkout. When it arrives, walk around the crate with the driver and write any damage on the bill of lading before signing; once you sign clean, a claim gets very hard.Collection from Acworth, GA is available for Schulz. Call, text or chat and we will help you check the 56 by 23 by 42 inch footprint against your space first: 866-774-7743.WarrantySchulz covers the unit for 1 year and the pump for 2 years. Keep your proof of purchase and note the commissioning date.Standard advice worth repeating: do not open the pump, motor or starter before a claim is raised. A disassembled unit is normally treated as ineligible no matter how sound the diagnosis was. Call us and we will start the claim with the manufacturer.
Brand:Schulz of AmericaCategory:Air CompressorSKU:932.9345-0Tags:Air compressor, Electric Air Compressor, freight, Professional Shop Use Air Compressor, Stationary Air Compressor, Two Stage Air Compressor